Click Speed Tests: CPS, Mouse Buttons & Click Timing

Choose a tool by the question you want to answer: how fast you click, which button arrives, how far apart clicks land, or how a browser demo behaves. These tools measure different events, so their results are not interchangeable.

Start with the result you need

Measure my general clicking rate

CPS test

Count clicks over 5, 10 or 30 seconds. Use the same duration for repeat comparisons.

Result: click count and clicks per second.

Check which mouse button registers

Mouse-button test

Check Left, Right, Middle or a side button. The pad counts presses and suppresses its context menu.

Result: last button and separate button counts.

Measure right-button clicking rate

Right-click test

Use a timed right-button pad with its context menu suppressed. A primary-click pad is a different test.

Result: right-button count and CPS.

Check the time between two clicks

Double-click test

Inspect the gap between registered primary clicks. Its 500 ms comparison is a fixed reference, not a reading of your Windows setting.

Result: last, fastest and average gaps in milliseconds.

Check an external auto clicker’s timing

Auto clicker speed test

Aim a primary-click sequence at the pad and compare arriving input with a target interval over 5, 10 or 30 seconds.

Result: CPS, average gap, target difference and gap spread.

Try generated events inside a browser page

Online auto clicker demo

Run the page’s A/B/C targets to explore its interval and repeat settings. It cannot click another tab or desktop app.

Result: counts from that page’s own demonstration.

Choose a specific input method or duration

Spacebar clicker test measures Space keydown events. Holding Space can produce keyboard-repeat events, so keep a held-key run separate from a test of distinct taps. Follow the page’s focus instructions so a control does not consume the key.

Clicking-method and fixed-duration counters
Tool	Use it for	Keep in mind
Jitter click test	A 5 or 10 second sample using your chosen clicking method.	The counter does not identify the technique.
Butterfly click test	A 5 or 10 second sample for comparing attempts on the same setup.	Keep the device, duration and input method consistent.
Drag click test	Count registered primary clicks over 5 or 10 seconds.	Moving the pointer alone does not create counted clicks.
1 second CPS test	A very short, fixed-duration sample.	The start and finish have a large effect on a short sample.
60 second CPS test	A count averaged over one full minute.	Pauses are included in the full-window average.
100 second CPS test	A count averaged over 100 seconds.	Compare with the same duration, not a one-second burst.

These technique-specific counters share the basic job of counting arriving events. Their titles do not mean the page can verify a technique, separate manual input from automation, or diagnose mouse hardware.

Understand what each number measures

Counts, rates and intervals answer different questions
Measurement	Meaning
Click count	The events received by the selected pad. Primary-click counters use `click`; the right-click and mouse-button tools count the relevant `mousedown` presses.
CPS	Final count ÷ the selected test duration. For example, 40 clicks in 5 seconds = 8 CPS. It does not describe every gap within that window.
Equivalent interval	1000 ÷ CPS. At 8 CPS, a uniform pace would be 125 ms. This conversion is not a measurement of the actual spacing of clicks.
Average gap	The mean time between consecutive recorded clicks. N clicks produce N−1 gaps. The auto clicker speed test measures these gaps separately from full-window CPS.
Gap spread	In the auto clicker speed test, sample standard deviation describes how much recorded gaps vary. A low mean difference from the target does not by itself mean every gap was close.
Spacebar count	Space `keydown` events, including repeat events when holding a key. This is not necessarily a count of distinct presses.

Use the click interval calculator when you want a theoretical CPS-to-milliseconds conversion. To compare measured runs, keep the same duration, device, browser and input method, and read the chosen tool’s rules before starting.

Keep the active test visible. Reset before a new comparison and do not mix mouse, touch, keyboard activation or automated input into a result you intend to call a manual mouse test. Each tool reports what reaches its own page; it does not measure whether another app successfully completes an action.

Frequently asked questions

Which click test should I use first?

Use the CPS test for a general clicking-rate sample. Use the mouse-button test if you need to know whether Left, Right or another button registers. If you are checking an external auto clicker’s timing, use the auto clicker speed test, which also measures average gaps and their spread.

What does CPS measure?

CPS means clicks per second. A completed timed test divides its recorded count by the selected duration: 40 clicks over 5 seconds is 8 CPS. It describes events received by that page, not a universal rating of your mouse, skill or performance in another application.

Is 1000 divided by CPS the actual average gap between clicks?

Not necessarily. It gives an equivalent interval for an evenly spaced pace. A burst followed by idle time can have the same full-window CPS as evenly spaced clicks. Use the auto clicker speed test for the measured mean of consecutive gaps, and keep that value separate from the CPS conversion.

Can these counters prove that a result is manual or identify a clicking technique?

No. A count does not identify how the input was produced. Mouse, touch, keyboard activation or an external clicker can produce events that some pads accept. Keep the input method, duration, device and browser consistent when comparing runs, and read the selected tool’s counting rules.

Do right clicks and spacebar presses belong in the same CPS test?

Use the dedicated tools. The right-click test records right-button presses; the mouse-button test separates buttons. The spacebar test records Space keydown events and can include keyboard repeat when a key is held. Those counts are not interchangeable with a primary-click test or a count of distinct manual taps.

Can these browser tools click another website or Windows app?

No. The counters measure input received by their own pads, and the online auto clicker demo generates events only on its own A/B/C targets. A separate Windows application is needed to send input to desktop coordinates. Free Auto Clicker uses normal input on a visible foreground target; it does not click inside a hidden or minimized window.

Need repeatable clicks in a Windows app?

Choose the Windows auto mouse clicker for a separate task that needs real desktop coordinates. It sends normal input to a permitted, visible foreground target. Use a short repeat limit and the F8 emergency stop; it does not click inside hidden or minimized windows.

Download Free Auto Clicker Open the browser demo

Click Speed Tests: Choose What to Measure